Skip to content
KingpinLoadsTruck dispatch desk

Flatbed load securement: the rules, drawn on a real load

By Ronald, truck dispatcherUpdated October 2026

Flatbed trailer with a secured steel coil, side view48' 0"

Quick answer

Flatbed load securement means tying each article of cargo to the trailer so it can't shift, fall or blow off. Under FMCSA's 49 CFR Part 393 you need a minimum number of tie-downs based on the article's length, enough combined working load limit to hold half its weight, and checks within the first 50 miles and along the way.

Flatbed load securement is the part of open-deck work that never goes away. Every load, every time, you decide how many tie-downs to throw, what gear to use and where to put it, then you stop and check it. The federal rules in 49 CFR Part 393, Subpart I set the minimums. This guide shows how those rules work on a real load, drawn to scale.

What the rules ask for

The general rules apply to every article of cargo on a flatbed:

  1. It must not shift or fall. The securement system has to hold the cargo against set forces: under the working load limits of the gear, 0.435 g forward, 0.5 g rearward and 0.25 g sideways. Cargo that isn't fully inside the vehicle also needs a downward force of at least 20% of its weight.
  2. Enough tie-downs for the length. One tie-down for an article 5 feet or shorter and 1,100 pounds or lighter; two up to 10 feet; then one more for every extra 10 feet or part of it. If the article is blocked in front by a headerboard, bulkhead or other secured cargo, one tie-down per 10 feet.
  3. Enough working load limit for the weight. The tie-downs' working load limits, added together, must reach half the article's weight. A tie-down running from the deck over the cargo to the other side counts at its full limit; most other set-ups count at half.
  4. Gear in good shape. No knots, damage or weakened parts, and every tie-down adjustable and tight.

Source:49 CFR 393.102, minimum performance criteria: WLL must handle 0.435 g forward, 0.5 g rearward, 0.25 g lateral; downward force of at least 20% of the article's weight when not fully contained · checked 2026-1049 CFR 393.110, minimum number of tiedowns · checked 2026-1049 CFR 393.106, general cargo securement requirements (aggregate WLL) · checked 2026-10

The rules on a real load

Here is an EXAMPLE: one crated machine, 24 feet long and 36,000 pounds, not blocked in front, secured with 4 inch straps marked at 5,400 pounds working load limit, running over the crate to the far side.

EXAMPLE deck plan: 24 ft crate, 36,000 lb, four 4 in strapsFRONT123424 FT / 36,000 LB / 4 TIE-DOWNS AT 5,400 LB EACHAGGREGATE WLL 21,600 LB / REQUIRED 18,000 LB (HALF THE WEIGHT)EDGE PROTECTORS SHOWN AT EACH CROSSING. EXAMPLE LOAD.

The length rule asks for four tie-downs: two for the first 10 feet, plus two for the remaining 14 feet. The weight rule asks for 18,000 pounds of working load limit, half of 36,000. Four straps at 5,400 pounds give 21,600, so four meets both rules. Edge protectors go wherever a strap crosses the crate's corners.

Now a second EXAMPLE with different numbers:

Example
Article
Steel pipe bundle
Length / weight
32 ft / 42,000 lb
Gear
Grade 70, 3/8 in chain
By length
5 tie-downs
By WLL (21,000 lb)
4 tie-downs
Minimum
5 chains
An unblocked 32 ft pipe bundle. Unmarked Grade 70 3/8 in chain counts at 6,600 lb under the 393.108 table.

Source:49 CFR 393.108, working load limits: marked WLL controls; default table (4 in webbing 4,000 lb, Grade 70 3/8 in chain 6,600 lb) · checked 2026-10

Here the length rule wins: five chains, giving 33,000 pounds of working load limit against 21,000 needed. Run the same check for any piece with the load securement calculator.

Step by step on the deck

  1. Know the load before you arrive. Commodity, weight, length and any shipper rules decide the gear you bring; our load securement equipment guide lists the kit and its ratings.
  2. Block forward. A headerboard or secured cargo in front lowers the tie-down count and protects the cab.
  3. Place the freight. Keep weight centered and spread over the axles; check the scale ticket before you leave.
  4. Count, then throw. Meet both the length and the weight rules, and space tie-downs along the article.
  5. Protect every edge. Corner protectors, sleeves or V-boards wherever a strap meets a sharp or hard edge (see flatbed dunnage and V-boards for what each one does).
  6. Tighten evenly. Every tie-down snug, none doing all the work.
  7. Tarp if required. Tarps go over the secured load and need their own straps or bungees.
  8. Re-check. Within 50 miles, then at every change of duty status, every 3 hours of driving or 150 miles, whichever comes first.

Source:49 CFR 392.9, inspection of cargo and cargo securement devices · checked 2026-10

Straps or chains

Both are legal when they're rated and in good shape; the freight decides.

  • Synthetic straps (usually 4 inch) suit finished goods, lumber, crates and anything a chain would scar. They're light and quick to throw, but they cut on sharp edges, so they need protectors wherever they touch a hard corner.
  • Chains with binders suit steel, pipe, coils and machinery: heavy, hard freight where a strap would wear through. They're heavier to handle and can damage soft or painted freight.
  • Mixed loads often use both: chains on the heavy pieces, straps on the rest.

Whatever you use, the rules on gear are short and strict: no knots, no damaged or weakened parts, and edge protection that resists abrasion, cutting and crushing wherever a tie-down could be cut. Retire a strap with cuts or burns, and a chain with stretched or cracked links.

Source:49 CFR 393.104, standards for securement devices: no damaged or weakened components (b), no knots (f)(1), edge protection where a tiedown would be cut or abraded, resisting abrasion, cutting and crushing (f)(4) · checked 2026-10

When commodity rules take over

FMCSA has extra rules for certain freight in sections 393.116 to 393.136: logs, dressed lumber and building products, metal coils (how hauling steel coils works under 393.120), paper rolls, concrete pipe, intermodal containers, automobiles, heavy vehicles and machinery, crushed vehicles, roll-off containers and large boulders. When your cargo falls under one of them, that section's requirements apply on top of, or instead of, the general count. Coils and heavy machinery are the two most open-deck carriers meet.

Source:49 CFR Part 393 Subpart I, protection against shifting and falling cargo: general rules 393.100-393.114, commodity rules 393.116-393.136 (logs, lumber, metal coils, paper rolls, concrete pipe, containers, vehicles, heavy machinery, crushed vehicles, roll-off containers, boulders) · checked 2026-10

Common mistakes

  • Counting by habit. "Four straps on a lumber load" isn't a rule. Length and weight decide it every time.
  • Mixing up marked and unmarked gear. Unmarked straps fall back to the federal default table; a worn tag isn't a tag.
  • Forgetting the weakest link. A tie-down is only as strong as its winch, binder or anchor point.
  • Skipping the 50 mile check. Straps settle and loads shift in the first hour.
  • No edge protection on finished goods. Damaged freight turns into a claim even when the load stayed put.

What it means for your pay

Securement is real work: an hour or more on a heavy or tarped load, often in the weather. It belongs on the rate con as securement time or built clearly into the rate, and tarps as their own line. Price a load with the extras in the flatbed rate calculator.

Our flatbed dispatch desk asks what gear you carry before offering freight, puts securement and tarp pay on the rate con, and only offers loads you can legally secure. The broker sends the rate confirmation straight to you, and you can say no to any load.

Questions people ask

01How do you secure a load on a flatbed?

Block the freight forward against a headerboard or other secured cargo where you can. Count the tie-downs the length rule asks for, then make sure their combined working load limit reaches half the weight. Spread them along the article, protect every edge they cross, tighten evenly and re-check within the first 50 miles and at every stop after that.

02What counts as improper load securement?

Too few tie-downs for the article's length, too little combined working load limit, damaged straps or chains, loose or unadjusted tie-downs, cargo that can shift or fall, and ignoring a commodity-specific rule such as the coil or lumber rules. Inspectors write these up as cargo securement violations, and serious ones can put the vehicle out of service.

03Do flatbed loads need edge protection?

FMCSA requires edge protection when a tie-down would be cut or worn by the cargo's edge, and the protection must resist that abrasion and cutting. In practice, synthetic straps over any sharp or hard edge need protectors. They also keep the strap from cutting into the freight, which shippers care about on finished goods.

04How often do you need to check a flatbed load?

Within the first 50 miles after loading, then whenever you change duty status, after 3 hours of driving or every 150 miles, whichever comes first. Adjust any tie-down that has loosened. Drivers of sealed loads they can't inspect are exempt from the en-route checks, but open-deck freight is almost never sealed.

Written by

Ronald, Truck dispatcher

Ronald is a truck dispatcher with 8 years of experience in trucking. Ronald writes the KingpinLoads guides and calculators for carriers who run their own trucks, and every rule in them is checked against its source.

Updated October 2026

Get dispatched

Securement is work. It should be on the rate con.

We quote securement time and tarp pay before you load, and never book freight you can't secure. Every load is your call.

  • You approve every load
  • Rate con comes straight to you
  • No contract, 30 days notice
  • No setup fee, no haul no pay

Start flatbed dispatch

Step 1/3

  1. Truck (current)
  2. Authority
  3. Contact
What do you run?
How many trucks?

No contract, no setup fee. You approve every load.